ECUHELP KT200 is tested able to read and write Flash & EEPROM on Bench / via OBD / in BDM & JTAG for more than 5400 ECU and over 500 TCU. Then how to use ECUHELP KT200 ECU Programmer?
Download ECUHELP KT200 software.
As known, there is ECUHELP KT200 auto version, full version and offline version.
1. ECUHELP KT200 auto version software (online version and 7 license available).
2. Download ECUHELP KT200 full version software (Also online software)
3. ECUHELP KT200 offline workstation software download source
Firstly, install ECUHELP KT200 offline dongle (also named as local server), then the offline software.
Operation tips:
1. win defender + Antivirus disabled As ADMIN
2. install both the x32/x64 patches
3. install drivers for device
4. install hardware+power
5. Please install software in Disk C://
Also:
KT200 software no need to register and activate.
Compatible with any pc(no limit volume of PC)
Operating system: Windows 7, Windows 8/8.1, Windows 10, Windows 11
Minimum Recommended Requirements: CPU > 2.5 GHz (Intel i5, i7), RAM > 8GB
Alright, To open the ecuhelp kt200 software, please do the following things:
Make sure good internet (for online version)
Go to Service to change a server (any of China, Germany and Hongkong)
Set time and timezone auto
Turn off windows defence
Set timezone to same as server
Use VPN and set VPN to where server is at
Restart PC
Make sure tool is plugged in
ECUHELP KT200 Questions and Answers Question:ECUHELP KT200 open device error solution.
Answer: This is the first time when the software is installed and the driver cannot be detected. Turn off this error message and continue the installation, and then install the driver in the device manager (Path: Device manager -> Universal Serial Bus Controller -> DFB-Technology DFOX); In another method: C -> KT200-Master -> remote -> driver Question:Disable Driver Signature Enforcement.
Answer: Usually, it is needed for Win7 installation.
1) Reboot the computer, hold F8
2) Enter “safe mode”, and select “Disable Driver Signature Enforcement”.
3) Reboot the computer.
Done!
If WIN10 needs to Disable Driver Signature Enforcement, the operation path is contained in the install package, path: C ->KT200-master ->remote -> Run in win 10, then the computer will reboot.
Note: Win10 professional / Business install no problem, and Win10 Home is not compatible.
Read Article: How to Disable Automatic Driver Signing in Windows 10 and Windows 7?
How to Reinstall ECUHELP KT200 software?
Please go to C disk and manually delete the folder “KT200-master”, ensure delete all empty before reinstall the software.
How to solve ECUHELP KT200 software auto close?
If the software auto close or the drivers button is gray, please check if you turn off Defender in Windows Security and the antivirus protection.
Operation:
1)Select Start and type "Windows Security" to search for that app.
2)Select the Windows Security app from the search results, go to Virus & threat protection, and under Virus & threat protection settings select Manage settings.
3)Switch Real-time protection to Off.
Another possible reason and solution:
There are 3 .dll files in the folder “KT200-Master” including Gcheck.dll, securityAcess. Dll, wuzi.dll, if there is 4 .dll files, it may be implanted with a virus. It will cause KT200 software auto close or not open directly.
One point to pay attention: when the software is started, dfb2xx.dll will pop up, and then disappear automatically, it is normal.
KT200 software "correct your time" solution
In Win 10: Right click the time at the right corner of the computer, select “Adjust date / time”, turn on “Set time automatically”, then click on “Sync now” below Synchronize your clock.
In Win7: Right click the time at the right corner of the computer, select “Adjust date / time”, then select “ Internet time”, and tick off “Automatically synchronize with an Internet time server.
Solution of Error:126 /"api-ms-win-crt-runtime-i1-1-0.dll” is missing/Visual C++ setup failed Error 1: Cannot load file libcrypto-3.dll Error:126
Error 2: "api-ms-win-crt-runtime-i1-1-0.dll” is missing”
Error 3: Visual C++ setup failed
Solution: Install the patch package corresponding to the system, and it can run normally.
Free download Vc_redist.x86 ( 32-bit system)
Free download Vc_redist.x64 (64-bit system)
Possible reason:
EDC16 c35 has 2 chips including 561/2 and 563/4, and their wiring method is not the same, also please ensure if the ECU is able to normally
communicating.
How to get the password when R / W in Boot mode?
Method 1. Insert ECUHELP KT200 into the car to find the password, and then come back to read and write in Boot mode. For example, SID208, please refer to the manual.
Method 2. Extract password.
After reading out, it will be saved to KT200 and named as password_adv.bin.
How to solve no ECU info displayed at the left corner of kt200 software?
Free download this auto.txt and put it into folder "KT200-Master".
KT200 "Selection driver not active” Solution
I have problems with the KT200 programmer "Selection driver not active", can you provide information on how to figure out this issue?
Possible solutions to the problem are:
1.Maybe tool is not recognized. To fix this issue, try resetting your PC ,unplug and plug the usb again and will be fine.
2.or driver issue, check device manager first, and then watch the video on how to update the driver:
3.It is also possible that your firewall is turned on and your antivirus is not uninstalled. If this is the case, uninstall the KT200 software, turn off all firewalls, uninstall the antivirus, and then reinstall the KT200 software.
![[EU Ship] ECUHELP KT200 II ECU Programmer Full Version with Offline Dongle for Car Truck Motorbike Tractor Boat,R/W ECU Bench/OBD/BOOT/BDM /Jtag Mode](/uploads/item-x300/171136130037011118.webp)
![[Suitcase] ECUHELP KT200 ECU Programmer, Read Write Car Truck via OBD / on Bench / in Boot Jtag [Get Free KTflash]](/uploads/item-x300/171567677819843923.webp)